Why Spring Dimensions Drift After Long Runs
Every spring maker knows the feeling. You set up a machine on Monday, hit ±0.01mm all day, and by Friday the free length has crept 0.05mm and the load test is drifting out of tolerance. Nothing "broke." The machine just stopped holding size. If you have chased this problem on a CAM machine, a CAMLESS machine, or a torsion setup, you have probably already suspected the truth: dimensional drift after long runs is almost never an electronics fault. It is wear, thermal change, and mechanical compliance stacking up in ways the control cannot see.
This is the topic nobody puts in the brochure, so let's walk through the real causes and the fixes that actually work in production.
The Four Things That Cause Drift
GUIDE AND SLIDER WEAR. Every coiling point contact wears. On entry-level machines this shows up in weeks; on well-built machines it takes months. Once the guide clearance grows, wire position at the forming point moves, and pitch or diameter shifts by a few hundredths.
THERMAL GROWTH. Servo motors, gearboxes, and cams all warm up over a shift. A 10-15°C rise in a 400mm feed box translates to measurable length change. Machines that hold size over 8-hour runs are usually machines whose feed box structure is rigid enough that this effect stays inside the tolerance band.
BACKLASH IN THE DRIVE TRAIN. Cam machines accumulate backlash at the cam followers and linkages. Servo CAMLESS machines accumulate it at the ball screw and reducer. Either way, the symptom is the same: a machine that repeats well when warm and slowly loses position when the load pattern changes.
WIRE STOCK VARIATION. Diameter tolerance and tensile variation in the incoming coil change spring-back. A machine with ±0.01mm positioning cannot fix a wire that varies by 0.02mm in diameter.
What the Data Looks Like in the Field
A Vietnamese spring factory running the HSM-CNC20 since 2010 reported a 35% increase in daily output after the first 8 months, with ±0.01mm accuracy holding steady — not on day one, but across years of production. That number is meaningful because it is a long-run number, not a setup number. A user in Shenzhen running two HSM-CNC20 units and one HSM-CNC08 put it more bluntly: the machine is stable, durable, and easy to set. Easy to set matters here, because dimensional drift is often really a repeatability-of-setup problem — if the setup was marginal, the drift shows up sooner.
Drift by Machine Type
Machine type | Typical drift source | Fix priority |
Cam coiling machine | Cam follower and slider wear | Wear parts, lubrication interval |
CAMLESS servo coiler | Ball screw and reducer backlash | Backlash compensation, reducer grade |
Torsion spring machine | Leg angle mechanism compliance | Tooling rigidity, servo tuning |
Wire bending equipment | Bend pin wear, feed slip | Tooling material, feed roller pressure |
Five Fixes That Hold Tolerance
TUNE THE SETUP, NOT THE PART. Adjust the machine so the target dimension sits in the middle of the tolerance band, not at the edge. A spring running at the high limit has nowhere to drift but out.
LOG THE FIRST AND LAST PIECE. Measure the first good part of the shift and the last one, and record the difference. A drift of 0.01mm per shift is a wear signal, not a fault.
REPLACE WEAR PARTS ON HOURS, NOT ON FAILURE. Guide inserts, bend pins, and feed rollers should be swapped on a planned interval derived from your own measurement log.
CONTROL THE ROOM. Machines running in an uncontrolled workshop with 15°C swing will drift. A small enclosure or a stable corner of the floor does more for repeatability than another axis of servo.
MATCH TOOLING TO THE JOB. Heavy wire needs tooling that resists deflection under load; light wire needs tooling that does not mark the surface. For heavy-duty work such as garage door spring coiling, tooling stiffness dominates the drift story. For light work, feed grip does.
The Buying Lesson
When buyers compare CNC wire bending equipment price, the price difference between machines very often maps to these invisible details: guide and slider material grade, the design of the crank arm, and whether the wire feed box is a one-piece structure. A one-piece feed box holds alignment under thermal and load cycling; a bolted assembly creeps. A Turkish customer who bought a single machine in 2018 bought a separate length-measuring gauge because he did not trust the machine to hold size — and later found the machine stayed stable without it, so in 2026 he came back for two more.
If you want to see what stable output looks like in practice, watch a stable torsion spring machine video and compare the pitch consistency across a 500-piece run, not across five pieces.
So here is my question for the shop floor: on your machines, does the dimension drift mostly happen in the first two hours of the shift or the last two? That answer tells you whether you are fighting thermal growth or wear — and they need completely different fixes.

Comments