top of page
Search

Why Spring Dimensions Drift After Long Runs

380154999
11 minutes ago
4 min read


The Problem Every Shop Eventually Sees


You run a spring making machine for six hours straight. First part checks at ±0.01mm. By hour five, the outer diameter has crept up 0.03mm and the free length is off by 0.15mm. Nothing changed in the program. So what changed in the machine?


Dimension drift on long production runs is one of the most common complaints we hear from spring shops, and it almost never comes from the CNC control itself. It comes from five physical sources. Understanding them tells you whether your machine design is fighting you or working with you.


Source 1: Thermal Growth in the Feed System


Wire feed rollers, straighteners, and the feed box all generate heat from friction. Over a four-hour run, a feed box can rise 8-12°C above ambient. On a machine with a separate feed box mounted on a bracket, that heat moves the feed reference point relative to the tooling.


On an INTEGRAL FEED BOX DESIGN, where the feed mechanism and the slide base share one rigid casting, thermal expansion is distributed across a single structure instead of being amplified by a bolted joint. This is one reason we build the feed box as one piece on the HSM-CNC20 — shops running 0.2-4.0mm wire report holding ±0.01mm across full shifts rather than watching the first hour drift away.


Source 2: Wear at the Slide and Cam Contact


Every coiling cycle puts the slide against its guideway and the cam against its follower. Soft guide materials wear into a slightly larger clearance within months, and that clearance shows up as inconsistent spring OD.


What to look for when evaluating any machine:


  • Slide and guideway hardness and surface treatment — hardened and ground surfaces hold clearance far longer than case-hardened soft stock

  • Cam profile finish — a rough cam accelerates follower wear and changes timing

  • Curved arm geometry — a properly designed CURVED ARM keeps the lever ratio stable through the stroke instead of changing mechanical advantage mid-cycle


These details are invisible on a spec sheet. They are exactly what one customer examined during a factory visit in September 2026 — the wear-resistant slide materials, the curved arm design, the one-piece feed box — and why they chose three HSM-CNC20 cam machines despite a higher price than competing quotes.


Source 3: Backlash Accumulation in Camless Axes


On a 3D CNC WIRE BENDING MACHINE FOR OIL SEAL SPRING PRODUCT, camless axes drive the tooling directly through servo motors and ball screws. Ball screw backlash grows slowly with use. If the control does not compensate, every reversal in the tool path adds a few microns of error.


The fix is mechanical discipline plus software compensation:


  • Preloaded ball nuts from the start

  • Backlash measurement built into the maintenance schedule, not discovered through scrap

  • Control software that stores per-axis compensation values and applies them automatically


On camless platforms like the HSM-CNC1045 with wire rotation, dimensional drift over long runs usually traces to backlash in the rotation axis before anything else. Measure it quarterly.


Source 4: Wire Lot Variation


A new wire coil can differ from the last by 0.005-0.01mm in diameter and by several percent in tensile strength. The machine did not drift — the material did. Shops that track drift without tracking wire lot numbers chase ghosts.


Practical habit: log the wire lot on every setup sheet, and when dimensions shift, check the lot before touching the machine.


Source 5: Tooling Wear and Setup Relaxation


Coiling points, pitch tools, and cutoff blades wear. So do the clamps that hold them. A tool that moves 0.02mm in its holder changes the spring more than any servo error will. Torque-check tooling clamps at the start of each shift.


Machine Comparison: Where Drift Resistance Comes From


Model

Wire Range

Type

Feed System

Best Fit for Long Runs

HSM-CNC08

0.08-1.0mm

Cam

Compact

Micro springs, electronics

HSM-CNC20

0.2-4.0mm

Cam

Integral feed box

General purpose, high volume

HSM-CNC30

0.8-3.0mm

Cam

Integral feed box

Mid-size compression springs

HSM-CNC40

1.8-4.5mm

Cam

Integral feed box

Automotive, heavy duty

HSM-CNC60

2.0-6.0mm

Cam, optional wire rotation

Integral feed box

Large wire, suspension

HSM-CNC1008

0.1-1.0mm

Camless

Servo direct

Micro springs, quick setup

HSM-CNC1025

0.2-2.5mm

Camless

Servo direct

Mixed low-volume production

HSM-CNC1045

1.8-4.5mm

Camless with wire rotation

Servo direct

Complex 3D forming


What Field Data Suggests


A Vietnamese customer has run an HSM-CNC20 since 2010. After eight months of production, daily output rose 35% while holding ±0.01mm — the kind of result that only happens when drift is controlled at the mechanical level, not corrected part by part.


A Brazilian customer bought two HSM-CNC20 machines in 2022. They set up a WeChat service group for repairs. It has never been used.


A Turkish customer bought a first machine in 2018 and, skeptical of stability, also bought a length gauge. The gauge turned out to be unnecessary. In October 2026 they ordered two more 08 coiling machines without hesitation.


Questions Worth Asking Before Your Next Machine Purchase


When you evaluate a spring making machine, ask the builder three things: how the feed box is constructed, what the slide and guideway materials are, and how backlash compensation is handled in the control. Then ask to see a machine run for six hours, not six minutes.


What drift patterns do you see on your current machines — gradual creep, step changes, or lot-to-lot jumps? The pattern usually points straight to the source.

 
 
 

Recent Posts

See All
Why Spring Dimensions Drift After Long Runs

Every spring maker knows the feeling. You set up a machine on Monday, hit ±0.01mm all day, and by Friday the free length has crept 0.05mm and the load test is drifting out of tolerance. Nothing "broke

 
 
 

Comments


Welcome to DONGZHENG

AND GET YOUR SAMPLES READY

Limei Industrial zone, Dalang, Dongguan, Guangdong

+8613809822984
 

  • Facebook
  • Twitter
  • YouTube
  • LinkedIn

© 2026 by DONGHENG

bottom of page